Windows 10 Upgrade Keeps Restarting (Fixed with 3 Ways)

Posted by @Ada

May 11, 2018

This article will introduce you how to solve Windows 10 upgrade keeps restarting issue. And it will offer you some tips to stop this issue happening again.

Scenario

My Windows 10 computer keeps restarting to finish installing 2018-02 Cumulative Update for Windows 10 Version 1709 for x64-based Systems over and over again. After each restart, I look at View installed update history and it says "Requires a restart to finish installing". Is there anything I can do to help this update install successfully or stop it from restarting over and over again. The security Update 2018-023 installed successfully on 2/7/18. Thanks!

How to fix Windows 10 upgrade keeps restarting?

Recently, some users complain about Windows 10 continuous reboot after Windows 10 update. The Windows 10 reboot loop is nerve-wracking. No matter if you updated from Windows 8.1, 8 or 7, there is a big chance that you would get stuck in an infinite Windows 10 boot loop. 

Actually, there are two common factors that will cause the issue laptop keeps restarting after Windows 10 upgrde: bad registry entry and corrupted driver. Therefore, to fix this issue, you should remove bad registry entry and fix the damaged driver. Before you try to remove bad registry entry and fix the damaged driver, you can first try a quick fix – cancel automatically restart.

Cancel Automatically Restart

1. Continuously press F8 until the boot menu shows up and choose Safe Mode.

2. Boot the computer from Safe Mode and go to search after Windows boot up. Type sysdm.cpl and open sysdm.cpl.

3. Click Advanced > Settings under Startup and Recovery. Uncheck Automatically restart.

4. Click OK and reboot the computer.

Note: This method can stop Windows 10 from restarting. However, it will not solve the problem from the source. If you go to update your computer, the update may fail again. Therefore, after trying this quick fix, you can follow the methods below to fix Windows 10 infinite loading issue.

Remove Bad Registry

1. Open Run window and type regedit to open Registry Editor

2. Then, navigate to HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\WindowsNT\CurrentVersion\ProfileList;

3. Next, scan through the ProfileList IDs and remove any with ProfileImagePath found in it

4. Exit Registry Editor

5. Now, reboot your computer. It might fix the endless booting problem. If not, reinstall Windows 10 operating system.

Note: This action may be dangerous, so you’d better back up your registry key to avoiding any kind of disaster.

Fix Driver Issues

There are reports that Windows 10 conflicts with AMD graphics. If your computer is stuck in endless Windows 10 boot loop, that might be caused by the outdated driver issues. Try to fix the graphics drivers.

Step 1. Open the Control Panel, select the Performance and maintenance tab and choose System. Click on Device Manager and see if there is yellow exclamation point beside any of the listed hardware.

Step 2. Right-click on the device that has a yellow exclamation point beside and click "Properties." Under the "General" tab, click on "Troubleshoot" and follow the instructions to solve it.

Step 3. If Step 2 does not work, navigate again to the device and right-click on it. Click "Properties" and choose "Update Driver." Reboot your computer and see if the yellow exclamation point disappears.

Step 4. If Step 3 still does not solve the problem, you may need to reinstall the driver.

How to avoid “computer keeps restarting in Windows 10” happen again?

After fixing the issue Windows 10 upgrade keeps restarting, you might need to consider taking some prevention measures to prevent this issue or similar issue like computer keeps restarting on startup happening again. And the best prevention measure is to make an image backup. With an image backup, whenever you have Windows 10 infinite loading issue, or Windows 10 continuous reboot issue, or other system issues, you can always revert your system to the previously good state.

To backup your computer, it is recommended to use free AOMEI Backupper. It is easy-to-use software that comes with many powerful features. It supports you to backup system, partition, disk, and files. With the backup created by AOMEI Backupper, you can easily restore to the previous state if something bad happens to your computer. Even when you cannot boot your computer, you can also restore from bootable disk.

Next, I will walk you through the detailed steps to backup your computer.

Step 1. Download AOMEI Backupper and open this tool. Click Backup and select System Backup.

System Backup

Step 2. As the software will automatically choose the source for you, you only need to click Step2 to select another location as destination path. AOMEI Backupper supports many storage devices, so you can backup Windows to USB drive, internal hard drive, NAS, cloud drive, etc.

Task Name

Step 3. If you need to keep your backup up to date, you can click Schedule to automatically backup your system on a regular basis. By default, the regular backup will take incremental backup; it will not take you much backup disk space.

Step 4. At last, click Start Backup.

After creating system image backup, you will not need to worry Windows 10 upgrade failed and keeps restarting issue. If this issue happens again, you can always get your system back to normal with the backup created by AOEMI Backupper. Even if your computer hardware issues, the advanced version of AOMEI Backupper allows you to restore to a dissimilar hardware.

To make a summary: you can backup your system after fixing Windows 10 upgrade keeps restarting issue to prevent this issue or similar issues like Windows 10 updates keeps restarting happening again. And users who intend to upgrade or update your computer can also back your system in case upgrade or update failure.